Stanrose Envirotech India Pvt. Ltd.

Send Enquiry   |   Environment Policy  |   Search Products

An ISO 9001 : 2008 & 14001 : 2004 Certified Company

Stanrose® PUC WB (Concrete Sealer)                                                                                                                      
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Product Description :
Stanrose® PUC WB (water-based) is a premium quality 100% clear acrylic sealer that will enhance and protect previously coated, bare concrete, and other masonry surfaces. It is a single component that can be applied to both interior or exterior applications. Stanrose®PUC WB will apply milky white to ensure complete coverage, but dries to a transparent, durable gloss finish.

Where to use ?
Topcoat for Stanrose®PUC WB Solid Color Water-based projects
Patios (stone slabs)
Lanais (balcony)
Driveways / walkways
Pool Decks
Brick and Cement Plaster Surfaces

Key Advantages :
Stanrose® PUC WB is a water-based sealer that is user-friendly, as well as durable. Suitable for all kinds of surfaces, inside and out. Clean up is simple with just soap and water, no messy residues. Stir in Stanrose®PUC WB Slip Resistant Additive to make inclined surfaces or damp areas safer. This product can be applied over previously painted or stained surfaces.

How to Apply ?
1. Product Supplies
Stiff broom
Bristle brush to cut in
Tray and tray liner
1/4" - 3/8" nap roller cover and frame (synthetic)
Optional: airless sprayer, tip orifice should not exceed .017"

2. Product Preparation
For previously stained or painted: Scrape and sand all loose material prior to the application. To ensure adequate adhesion of sealer, scuff sand all remaining stain or paint. Reapplication of the old coating should be done to create an even uniform appearance. Stanrose® Cleaner Degreaser should be mixed 50/50 with water to remove light soils from the surface. Use Cleaner Degreaser at full strength for heavy oil or grease stains.

For Bare Concrete: Freshly poured concrete must cure for a minimum of 28 days. All concrete should be clean and free of laitance, oil, grease or dust. Use Stanrose®PUC WB Etching Solution to open the pours of the concrete and get it ready to be sealed. The surface should feel like 120-grit sandpaper, if not, etch again, be sure to rinse thoroughly. Allow 24 hours to dry before staining or sealing.

3. Product Application
Determine if the conditions are right for application: surface and air temperatures should be between 50° and 95° F, and should not fall below 40° for 24 hours after application. This will effect the dry time, and may cause blushing and loss of adhesion. Do not apply Stanrose®PUC WB if rain is expected within 12 hours of application.

This product can be applied with a brush/roller or an airless sprayer. When spraying, be sure to back roll the sealer to remove excess sealer; this will ensure an even finish. One coat of Concrete Sealer Wet Look is normally sufficient, however if 2 coats is desired, allow 2 hours of dry time between coats. Do not over apply, this can cause "blushing." The sealer will apply milky white and dry clear in approximately an hour. Horizontal and vertical should be applied in the same manner as above.

Dry Times : (Low temperatures or high humidity will effect dry times)
To touch: 1 hour
Recoat: 2 hours
Foot Traffic: 24 hours
Vehicular Traffic: 72 hours

Coverage will be anywhere from 100-250 square feet per gallon, depending on substrate and porosity of surface, please see the Product Data Sheet for specifics.

 

 

The manufacturer reserves the right to change the specifications. Stanrose products are guaranteed against material manufacture and are sold subject to company's Terms and Conditions of Sale. Whilst we endeavour to ensure that advice, specifications, recommendations and information given is correct, we cannot have control over how our products are applied and will not accept liability, directly or indirectly.

 

NAVIGATE

News & Events
Send Enquiry
Channel Partners
Contact Stanrose
Search Products

ABOUT STANROSE

Corporate Profile
Team Stanrose
Infrastructure

Quality Policy
Environment Policy

CREDIT

Copyright -
All rights reserved.

Stanrose Envirotech
India Pvt. Ltd.

UPDATE

For best performance Stanrose recommend you to update your browser.

Internet Explorer   |   Mozilla Firefox   |   Google Chrome

 

Self Leveling Flooring | Under Lay Flooring | Electrostatic Flooring | PU Screed Matt | Concrete Sealer | Concrete Repairing | Car Parking Deck System |
Epoxy Grout
| Water Proofing System | Heat Reflector | Epoxy Rust Protector | PU Rust Protector | Epoxy Structure Coating | PU Solvented Paint |
Anti Fouling Paint
| Epoxy IMO

Enquiry



























Enquiry